Why does my toilet tank runs every so often?

Perhaps the most common reason for a running toilet is an old flapper that needs to be replaced. When flappers get old, they don't seal the way they should, and this allows water to pass constantly from the toilet tank into the bowl.

Why does my toilet randomly run for a few seconds?

If a toilet randomly runs for a few seconds and empties without flushing, it's likely the result of a cracked toilet flapper, the chain being caught, the float needing to be lowered, or the refilling tube needing to be repositioned.

How do you fix a toilet that runs randomly?

If the tank water drips into the bowl, you'll have a toilet that randomly runs or runs continuously. Open your toilet tank lid, and perform a test flush. Watch as the handle pulls the chain, and make sure that there's enough slack for the flapper to return to its resting position.


Why do toilets run every 10 minutes?

In the vast majority of cases, the problem is with the flapper, which is the rubber seal between the tank and the bowl. When it's worn, or the chain is too short, water seeps into the bowl, and the fill valve cycles on as soon as the float falls below the cutoff level.

What causes toilet to run every 5 minutes?

Toilet tanks contain a float ball that is connected to the float arm. This plastic-like balloon can be the reason why your toilet water runs every 5 minutes. As the tank overflows when you flush, the float ball rises to a certain level to indicate it's time to stop.


How to Fix A Running Toilet GUARANTEED | DIY Plumbing Repair



Why does my toilet intermittently run?

A toilet that cuts on and off by itself, or runs intermittently, has a problem that plumbers call a "phantom flush." The cause is a very slow leak from the tank into the bowl. This problem is almost certainly caused by a bad flapper or flapper seat.

Why does my toilet run every 30 seconds?

If your float is too high, water will constantly drain into the overflow tube, which can make it sound like your toilet is constantly running. Take the lid off the toilet tank and watch the overflow tube. If water flows up into the tube after a flush, lower the float until the problem is resolved.

How do I know if my toilet flapper is bad?

The tell-tale signs that you might have a malfunctioning flapper are:
  1. Toilet water runs intermittently or for a longer amount of time than usual;
  2. Rippling water move in the bowl between flushes;
  3. Low flushing power and hissing “filling” sounds;
  4. Jiggling the toilet handle doesn't stop the toilet from flushing;


How often should toilet flapper be replaced?

The average toilet flapper lasts about 4 to 5 years. It is important that you replace your toilet flapper when needed to prevent damaging leaks.


What is Ghost Flushing?

Ghost flushing, also known as phantom flushing, occurs when the toilet tank flapper is no longer creating a watertight seal with the flush valve, causing water to unnecessarily leak into the toilet bowl.

Why does my toilet make noise periodically?

There are several things that could be causing your toilet to make either a gurgling noise or a loud noise, but the three most common reasons include calcium deposits that have accumulated over time on the inner portion of the pipes, faulty fill valves, or leaky toilet valves.

Can a gurgling toilet fix itself?

Can a Gurgling Toilet Fix Itself? It is possible the gurgling sounds go away on their own if the drain clog clears itself or you remove any debris from the vent stacks on the roof. If the issue lies in your main sewer line, you'll need the help of professional plumbers.

Can a phantom flush be fixed without calling a plumber?

While replacing a flapper can be done on your own through parts picked up at the hardware store, if you want to fix this issue quickly and correctly, you may just want to call a professional. If you have a spooky ghost flushing toilet or other plumbing problems, contact us today to see how The Plumber Guy can help.


Why does toilet tank keep refilling?

A chain that's too short or tangled won't allow the flapper to close and water will continue to leak into the bowl. This causes the fill valve to cycle on and off to refill the tank. A chain that's too long, or a flush rod that hits the tank lid, won't open the flapper wide enough to stay open for the full flush.

Are toilet flappers universal?

Are all toilet flappers universal? No. There are universal designs like the Fluidmaster flappers that replace most other flappers and there are specialty flappers for specific flushing systems.

How do you stop a flapper valve from leaking?

  1. TURN OFF THE WATER AND EMPTY THE TANK. Turn off the water supply at the wall and slush the toilet. Hold the handle down to allow as much water as possible out of the tank. ...
  2. REPLACE THE TANK BALL. Replace the tank ball if it is cracked or worn. ...
  3. REPLACING THE FLAPPER. Replace the flapper if it is cracked or worn.


Can you put Vaseline on a toilet flapper?

One easy, but temporary fix to make rubber toilet parts supple again is vaseline. The toilet must be drained and dried for this to work. Then, vaseline can be rubbed on the flapper and it's connecting washer until they become soft. The toilet should be filled and checked again.


Why does flapper stay open?

The typical causes for a toilet flapper won't close after flushing is the chain is short, flapper hinges mineral build-up, the air stuck in the flush valve, and the weight of the flapper. To fix this problem need to replace the flapper or chain adjustment.

How long should the flapper stay open?

The bottom line is that the flapper has to stay open long enough for the toilet to flush completely. If you have a contemporary low-flow toilet, the flapper can rise almost to the vertical position; it will then stay open long enough for the level of the water in the tank to fall to the rim of the siphon tube.

Why is my toilet flapper not closing?

Besides the chain resting in the incorrect hole, the chain itself can be the reason the flapper doesn't close. Check the chain for kinks or places where it may have bound up, resulting in not enough length for the flapper to close completely.

Why is my toilet still running after replacing flapper?

If you've tried replacing the toilet flapper but the toilet still runs, the flush valve seat is probably rough or pitted. You can replace the entire flush toilet flapper valve, but it's a big job.


Can a bad flapper cause a toilet to overflow?

When you press down on the flush handle, a rod arm connected to the flapper valve via a chain lifts the valve and allows water from the tank to drain out into the toilet's bowl. A bad flapper will not cause your toilet to overflow, but when the flapper valve malfunctions, you will be unable to flush your toilet.
Previous question
Is Nikka a girl name?